Cisco Device Management
Pada lab ini anda akan mengerjakan factory reset, password recovery, configuration backup, dan system image backup and recovery pada router Cisco. Anda juga akan mengerjakan upgrade IOS pada switch Cisco.
Gunakan Packet Tracer Cisco untuk latihan ini. Server generic pada Packet Tracer sudah built-in dengan TFTP server software.
Lab Topology
Factory Reset
1) View the running configuration on R1. Note that the hostname and interface have been configured
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#exit
R1#
%SYS-5-CONFIG_I: Configured from console by console
R1#show run
Building configuration…
Current configuration : 698 bytes
!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname R1
!
!
!
!
!
!
!
!
ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO2911/K9 sn FTX152447Z1
!
!
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
!
!
!
!
!
!
interface GigabitEthernet0/0
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
no shutdown
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface GigabitEthernet0/2
no ip address
duplex auto
speed auto
shutdown
!
interface Vlan1
no ip address
shutdown
!
ip classless
!
ip flow-export version 9
!
!
!
!
!
!
!
!
line con 0
!
line aux 0
!
line vty 0 4
login
!
!
!
end
2) Factory reset R1 and reboot
R1#write erase
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
%SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvram
R1#reload
System configuration has been modified. Save? [yes/no]:no
Proceed with reload? [confirm]
System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 2010 by cisco Systems, Inc.
Total memory size = 512 MB — On-board = 512 MB, DIMM0 = 0 MB
CISCO2911/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC disabled
3) Watch the boot up process as the router boots
Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340
program load complete, entry point: 0x80803000, size: 0x1b340
IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x3bcd3d8
Self decompressing the image :
########################################################################## [OK]
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x022F6000
— — — — — — — — — — — — — — — — — — — — — — — -
TOTAL: 0x022F6000
Rounded IOMEM up to: 36Mb.
Using 6 percent iomem. [36Mb/512Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
© of the Commercial Computer Software — Restricted
Rights clause at FAR sec. 52.227–19 and subparagraph
© (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227–7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134–1706
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupport
Copyright © 1986–2007 by Cisco Systems, Inc.
Compiled Wed 18-Jul-07 04:52 by pt_team
Image text-base: 0x2100F918, data-base: 0x24729040
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco CISCO2911/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FTX152400KS
3 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
249856K bytes of ATA System CompactFlash 0 (Read/Write)
4) The router should boot into the Setup Wizard. Exit out of the wizard and then confirm the startup and running configurations are empty.
Router>en
Router#show run
Building configuration…
Current configuration : 693 bytes
!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname Router
!
!
!
!
!
!
!
!
no ip cef
no ipv6 cef
!
!
!
!
license udi pid CISCO2911/K9 sn FTX152447Z1
!
!
!
!
!
!
!
!
!
!
!
spanning-tree mode pvst
!
!
!
!
!
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
shutdown
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface GigabitEthernet0/2
no ip address
duplex auto
speed auto
shutdown
!
interface Vlan1
no ip address
shutdown
!
ip classless
!
ip flow-export version 9
!
!
!
!
!
!
!
!
line con 0
!
line aux 0
!
line vty 0 4
login
!
!
!
end
5) Paste the configuration for R1 from answer number 1 back into the configuration and save
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#ip cef
R1(config)#no ipv6 cef
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#license udi pid CISCO2911/K9 sn FTX152447Z1
^
% Invalid input detected at ‘^’ marker.
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#spanning-tree mode pvst
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#interface GigabitEthernet0/0
R1(config-if)# ip address 10.10.10.1 255.255.255.0
R1(config-if)# duplex auto
R1(config-if)# speed auto
R1(config-if)# no shutdown
R1(config-if)#!
R1(config-if)#interface GigabitEthernet0/1
R1(config-if)# no ip address
R1(config-if)# duplex auto
R1(config-if)# speed auto
R1(config-if)# shutdown
R1(config-if)#!
R1(config-if)#interface GigabitEthernet0/2
R1(config-if)# no ip address
R1(config-if)# duplex auto
R1(config-if)# speed auto
R1(config-if)# shutdown
R1(config-if)#!
R1(config-if)#interface Vlan1
R1(config-if)# no ip address
R1(config-if)# shutdown
R1(config-if)#!
R1(config-if)#ip classless
^
% Invalid input detected at ‘^’ marker.
R1(config-if)#!
R1(config-if)#ip flow-export version 9
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#!
R1(config)#line con 0
R1(config-line)#!
R1(config-line)#line aux 0
R1(config-line)#!
R1(config-line)#line vty 0 4
R1(config-line)# login
% Login disabled on line 388, until ‘password’ is set
% Login disabled on line 389, until ‘password’ is set
% Login disabled on line 390, until ‘password’ is set
% Login disabled on line 391, until ‘password’ is set
% Login disabled on line 392, until ‘password’ is set
R1(config-line)#!
R1(config-line)#!
R1(config-line)#!
R1(config-line)#end
Password Recovery
6) Set the enable secret ‘Flackbox1’ on R1
R1(config)#enable secret Flackbox1
7) Configure the router to boot into the rommon prompt on next reload, and reboot the router. In a real world scenario you would enter the Break sequence on the keyboard when first powering up the router to access the rommon prompt
R1(config)#config-register 0x2120
R1(config)#end
R1#
%SYS-5-CONFIG_I: Configured from console by console
R1#cop
R1#copy ru
R1#copy run s
R1#copy run start
Destination filename [startup-config]?
Building configuration…
[OK]
R1#reload
Proceed with reload? [confirm]
System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 2010 by cisco Systems, Inc.
Total memory size = 512 MB — On-board = 512 MB, DIMM0 = 0 MB
CISCO2911/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC disabled
Readonly ROMMON initialized
rommon 1 >
CONFIG REGISTER CONCEPT
EARLY WARNING: JANGAN MAEN2 DISINI KLO GA NGERTI (ngerusakin router nanti ente)
Pengaturan konfig register ini akan menentukan langkah router ketika pertama kali booting up
Kita bisa cek dulu…apa yang dilakukan secara default oleh router pas booting up dengan command “confreg”
Config-register = semacam konfig “bios” komputer ala cisco…mau booting normal, ke tftp server, atau ke safe mode (di cisco namanya Rommon)
Default config-register adalah 0x2102
Artinya itu 0x2102 adalah boot normal (klo normal pasti ga masuk rommon yang pake “break” kan?)
8) Configure the router to ignore the startup-config when booting up, and reload the router
Readonly ROMMON initialized
rommon 1 > confreg 0x2142
rommon 2 > reset
System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 2010 by cisco Systems, Inc.
Total memory size = 512 MB — On-board = 512 MB, DIMM0 = 0 MB
CISCO2911/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC disabled
Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340
program load complete, entry point: 0x80803000, size: 0x1b340
IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x3bcd3d8
Self decompressing the image :
########################################################################## [OK]
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x022F6000
— — — — — — — — — — — — — — — — — — — — — — — -
TOTAL: 0x022F6000
Rounded IOMEM up to: 36Mb.
Using 6 percent iomem. [36Mb/512Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
© of the Commercial Computer Software — Restricted
Rights clause at FAR sec. 52.227–19 and subparagraph
© (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227–7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134–1706
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupport
Copyright © 1986–2007 by Cisco Systems, Inc.
Compiled Wed 18-Jul-07 04:52 by pt_team
Image text-base: 0x2100F918, data-base: 0x24729040
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco CISCO2911/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FTX152400KS
3 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
249856K bytes of ATA System CompactFlash 0 (Read/Write)
— — System Configuration Dialog — -
Would you like to enter the initial configuration dialog? [yes/no]:
Yang biasa dipake selain 0x2102 adalah 0x2142: angka 4 (bit ke 6) artinya IGNORE NVRAM
Biasanya klo mau reset password, confreg-nya dirubah pake kode ini, cek how to reset password
Jadi klo ada salah2 (kek harusnya ngetik 2142 jadi 2124, trus malah jadi ga bisa masuk…cek itu “42” dan “24”….biasanya BAUD rate-nya yg bikin console terminal kita ga kebaca)
Bisa di cek di cisco.com untuk config register-nya
Ganti config register ada 2 cara…dari rommon (commandnya confreg 0xXXXX) atau dari global config
Kita liat di show version di yang paling bawah…harus di reload dulu
9) The router should boot into the Setup Wizard. Exit out of the wizard
— — System Configuration Dialog — -
Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>
10) What do you expect to see if you view the running and startup configurations? Confirm this.
Run-Start config akan kembali ke factory reset karena router melewatkan loading startup config saat boot up. Startup config seharusnya tidak berubah dan konfigurasi sebelumnya masih ada disana.
Router#sh run
Building configuration…
!
hostname Router
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
shutdown
Router#show start
Using 757 bytes
!
hostname R1
!
enable secret 5 $1$mERr$J2XZHMOgpVVXdLjC9lYtE1
!
interface GigabitEthernet0/0
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
no shutdown
11) Copy the startup config to the running config. Do not miss this step or you will factory reset the router!
Router#copy startup-config running-config
Destination filename [running-config]?
757 bytes copied in 0.416 secs (1819 bytes/sec)
R1#
12) Remove the enable secret
R1(config)#no enable secret
13) Ensure the router will reboot normally on the next reload and you will be able to access the router
R1(config)#config-register 0x2102
R1(config)#end
R1#
%SYS-5-CONFIG_I: Configured from console by console
R1#copy ru
R1#copy running-config st
R1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration…
[OK]
R1#
14) Reboot the router to confirm
R1#reload
Proceed with reload? [confirm]
System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 2010 by cisco Systems, Inc.
Total memory size = 512 MB — On-board = 512 MB, DIMM0 = 0 MB
CISCO2911/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC disabled
Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340
program load complete, entry point: 0x80803000, size: 0x1b340
IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x3bcd3d8
Self decompressing the image :
########################################################################## [OK]
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x022F6000
— — — — — — — — — — — — — — — — — — — — — — — -
TOTAL: 0x022F6000
Rounded IOMEM up to: 36Mb.
Using 6 percent iomem. [36Mb/512Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
© of the Commercial Computer Software — Restricted
Rights clause at FAR sec. 52.227–19 and subparagraph
© (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227–7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134–1706
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupport
Copyright © 1986–2007 by Cisco Systems, Inc.
Compiled Wed 18-Jul-07 04:52 by pt_team
Image text-base: 0x2100F918, data-base: 0x24729040
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco CISCO2911/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FTX152400KS
3 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
249856K bytes of ATA System CompactFlash 0 (Read/Write)
Press RETURN to get started!
R1>
R1#show run
!
hostname R1
!
interface GigabitEthernet0/0
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
no shutdown
Configuration Backup
15) Backup the running configuration to Flash on R1. Use a suitable name for the backup file. Verify the configuration has been backed up.
R1#copy run flash:
Destination filename [running-config]?
Building configuration…
[OK]
R1#show flash
System flash directory:
File Length Name/status
3 33591768 c2900-universalk9-mz.SPA.151–4.M4.bin
4 696 demo
5 698 running-config
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[33848981 bytes used, 221895019 available, 255744000 total]
249856K bytes of processor board System flash (Read/Write)
16) Backup the R1 startup configuration to the TFTP server. Use a suitable name for the backup file. Verify the configuration has been backed up.
R1#copy running-config tftp
Address or name of remote host []? 10.10.10.10
Destination filename [R1-confg]?
Writing running-config….!!
[OK — 698 bytes]
698 bytes copied in 3.072 secs (227 bytes/sec)
R1#
IOS System Image Backup and Recovery
17) Backup the IOS system image on R1 to the TFTP server. Verify the configuration has been backed up.
R1#show flash
System flash directory:
File Length Name/status
3 33591768 c2900-universalk9-mz.SPA.151–4.M4.bin
4 696 demo
5 698 running-config
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[33848981 bytes used, 221895019 available, 255744000 total]
249856K bytes of processor board System flash (Read/Write)
R1#copy flash tf
R1#copy flash tftp:
Source filename []? c2900-universalk9-mz.SPA.151–4.M4.bin
Address or name of remote host []? 10.10.10.10
Destination filename [c2900-universalk9-mz.SPA.151–4.M4.bin]?
Writing c2900-universalk9-mz.SPA.151–4.M4.bin…!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK — 33591768 bytes]
33591768 bytes copied in 1.052 secs (3352658 bytes/sec)
R1#
18) Delete the system image from Flash and reload.
R1#delete flash
Delete filename []?c2900-universalk9-mz.SPA.151–4.M4.bin
Delete flash:/c2900-universalk9-mz.SPA.151–4.M4.bin? [confirm]
R1#show flash
System flash directory:
File Length Name/status
4 696 demo
5 698 running-config
2 28282 sigdef-category.xml
1 227537 sigdef-default.xml
[257213 bytes used, 255486787 available, 255744000 total]
249856K bytes of processor board System flash (Read/Write)
R1#reload
Proceed with reload? [confirm]
System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 2010 by cisco Systems, Inc.
Total memory size = 512 MB — On-board = 512 MB, DIMM0 = 0 MB
CISCO2911/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC disabled
Readonly ROMMON initialized
Boot process failed…
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
rommon 1 >
19) Use Internet search to find system recovery instructions for your model of router. Recover the system image using the TFTP server.
Buka webpage tersebut lalu cari section tftpdnld. Lalu pada R1 input command-command berikut.
rommon 16 > IP_ADDRESS=10.10.10.1
rommon 17 > IP_SUBNET_MASK=255.255.255.0
rommon 18 > DEFAULT_GATEWAY=10.10.10.1
rommon 19 > TFTP_SERVER=10.10.10.10
rommon 20 > TFTP_FILE=c2900-universalk9-mz.SPA.151–4.M4.bin
Cabut koneksi router dan tftp ke switch. Sambungkan langsung router dan tftp hingga proses download system image selesai.
rommon 21 > tftpdnld
IP_ADDRESS: 10.10.10.1
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 10.10.10.1
TFTP_SERVER: 10.10.10.10
TFTP_FILE: c2900-universalk9-mz.SPA.151–4.M4.bin
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n: [n]: y
Receiving c2900-universalk9-mz.SPA.151–4.M4.bin from 10.10.10.10 !!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Copying file c2900-universalk9-mz.SPA.151–4.M4.bin to flash.
Erasing flash at 0x607c0000
program flash location 0x60440000
rommon 22 > reset
System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 2010 by cisco Systems, Inc.
Total memory size = 512 MB — On-board = 512 MB, DIMM0 = 0 MB
CISCO2911/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 72/-1(On-board/DIMM0) bit mode with ECC disabled
Readonly ROMMON initialized
program load complete, entry point: 0x80803000, size: 0x1b340
program load complete, entry point: 0x80803000, size: 0x1b340
IOS Image Load Test
___________________
Digitally Signed Release Software
program load complete, entry point: 0x81000000, size: 0x3bcd3d8
Self decompressing the image :
########################################################################## [OK]
Cisco CISCO2911/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FTX152400KS
3 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
249856K bytes of ATA System CompactFlash 0 (Read/Write)
Press RETURN to get started!
R1>
IOS Image Upgrade
21) Verify SW1 is running C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX
SW1#show version
Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
Copyright © 1986–2005 by Cisco Systems, Inc.
Compiled Wed 12-Oct-05 22:05 by pt_team
ROM: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
System returned to ROM by power-on
Cisco WS-C2960–24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
24 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)
63488K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 0030.F2E1.CDDB
Motherboard assembly number : 73–9832–06
Power supply part number : 341–0097–02
Motherboard serial number : FOC103248MJ
Power supply serial number : DCA102133JA
Model revision number : B0
Motherboard revision number : C0
Model number : WS-C2960–24TT
System serial number : FOC1033Z1EY
Top Assembly Part Number : 800–26671–02
Top Assembly Revision Number : B0
Version ID : V02
CLEI Code Number : COM3K00BRA
Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image
— — — — — — — — — — — — — — — — — — —
* 1 26 WS-C2960–24TT 12.2 C2960-LANBASE-M
Configuration register is 0xF
22) Use the TFTP server to upgrade to C2960-lanbasek9-mz.150–2.SE4.bin
SW1#copy tftp flash
Address or name of remote host []? 10.10.10.10
Source filename []? c2960-lanbasek9-mz.150–2.SE4.bin
Destination filename [c2960-lanbasek9-mz.150–2.SE4.bin]?
Accessing tftp://10.10.10.10/c2960-lanbasek9-mz.150-2.SE4.bin....
Loading c2960-lanbasek9-mz.150–2.SE4.bin from 10.10.10.10: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK — 4670455 bytes]
4670455 bytes copied in 3.062 secs (122628 bytes/sec)
SW1#show flash
Directory of flash:/
1 -rw- 4414921 <no date> c2960-lanbase-mz.122–25.FX.bin
3 -rw- 4670455 <no date> c2960-lanbasek9-mz.150–2.SE4.bin
2 -rw- 1054 <no date> config.text
64016384 bytes total (54929954 bytes free)
SW1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW1(config)#boot system c2960-lanbasek9-mz.150–2.SE4.bin
23) Reboot and verify the switch is running the new software version
SW1#reload
System configuration has been modified. Save? [yes/no]:yes
Building configuration…
[OK]
Proceed with reload? [confirm]
C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
Cisco WS-C2960–24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
2960–24TT starting…
Base ethernet MAC Address: 0030.F2E1.CDDB
Xmodem file system is available.
Initializing Flash…
flashfs[0]: 3 files, 0 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 64016384
flashfs[0]: Bytes used: 9086465
flashfs[0]: Bytes available: 54929919
flashfs[0]: flashfs fsck took 1 seconds.
…done Initializing Flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4
Loading “flash:/c2960-lanbasek9-mz.150–2.SE4.bin”…
########################################################################## [OK]
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
TOTAL: 0x00000000
Rounded IOMEM up to: 0Mb.
Using 6 percent iomem. [0Mb/512Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
© of the Commercial Computer Software — Restricted
Rights clause at FAR sec. 52.227–19 and subparagraph
© (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227–7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134–1706
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 15.0(2)SE4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 1986–2013 by Cisco Systems, Inc.
Compiled Wed 26-Jun-13 02:49 by mnguyen
Initializing flashfs…
fsck: Disable shadow buffering due to heap fragmentation.
flashfs[2]: 2 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 32514048
flashfs[2]: Bytes used: 11952128
flashfs[2]: Bytes available: 20561920
flashfs[2]: flashfs fsck took 2 seconds.
flashfs[2]: Initialization complete….done Initializing flashfs.
Checking for Bootloader upgrade..
Boot Loader upgrade not required (Stage 2)
POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed
POST: PortASIC CAM Subsystem Tests : Begin
POST: PortASIC CAM Subsystem Tests : End, Status Passed
POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed
Waiting for Port download…Complete
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C2960–24TT-L (PowerPC405) processor (revision B0) with 65536K bytes of memory.
Processor board ID FOC1010X104
Last reset from power-on
1 Virtual Ethernet interface
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:17:59:A7:51:80
Motherboard assembly number : 73–10390–03
Power supply part number : 341–0097–02
Motherboard serial number : FOC10093R12
Power supply serial number : AZS1007032H
Model revision number : B0
Motherboard revision number : B0
Model number : WS-C2960–24TT-L
System serial number : FOC1010X104
Top Assembly Part Number : 800–27221–02
Top Assembly Revision Number : A0
Version ID : V02
CLEI Code Number : COM3L00BRA
Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image
— — — — — — — — — — — — — — — — — — —
* 1 26 WS-C2960–24TT-L 15.0(2)SE4 C2960-LANBASEK9-M
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 15.0(2)SE4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright © 1986–2013 by Cisco Systems, Inc.
Compiled Wed 26-Jun-13 02:49 by mnguyen
Press RETURN to get started!
SW1>